G8MNY > TECH 15.03.24 08:30z 122 Lines 6257 Bytes #148 (0) @ WW BID : 3299_GB7CIP Read: GUEST Subj: PA instability in ICOM IC735 Path: ED1ZAC<ED1ZAC<LU1DBQ<LU9DCE<VA3TOK<VE3CGR<CX2SA<GB7CIP Sent: 240315/0821Z @:GB7CIP.#32.GBR.EURO #:3299 [Caterham Surrey GBR] $:3299_GB From: G8MNY@GB7CIP.#32.GBR.EURO To : TECH@WW By G8MNY (Updated Apr 16) (8 Bit ASCII graphics use code page 437 or 850, Terminal Font) ________________________________________________________ ³ ÚÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ == == == ³ ³ ßßßß == ³ \ ³ ³ Rx 14.273.5 vfo A 12³ _ _ ³ ³ /~\ ÀÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ (_) (_) ³ ³ \_/ ____ IC-735 ³ ³ ßßß ~~~~~~""""""~~~ /' `\ ßßß /"~"\ [] ³ ³ 0 ÜÜÜ |(~) | ÜÜÜ | | ³ ³ Þ Þ Þ Þ Þ Þ ³ ~ ³ \._./ [] ³ ³ /~~\ ßßß Þ Þ Þ Þ Þ Þ | | ßßß == == == ³ ³ \__/ ÜÜÜ # # # # # # [] \.____./ ÜÜÜ [___] [___]³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ I have 2 of these rigs, an old one for /P use, & a clean one in the shack. I've been looking into a problem with my newer clean shack one. It has developed a fault (may have always been there?), on long overs, on low power, the Tx gain goes down & results in distorted Tx AF. Using 2 tone testing (Mic processor off), I checked the 2 stage push pull bias & it seemed to be thermally vicious cutting off the driver & PA when warm. ÚÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ³Two ³ _ /³ ³ RIG ³ ³DUMMY³ ³ ³ ³ToneÃÄÄ´_³ ³ MicÄÄ´UNDERÃÄÄÄ´LOAD ÃÄÄÄ´SCOPE³ ³Osc ³ LS\³ ³ TEST³ ³& O/P³ ³ ³ ÀÄÄÄÄÙ ÀÄÄÄÄÄÙ ÀÄÄÄÄÄÙ ÀÄÄÄÄÄÙ So I had previously turned up the PA bias to be OK on 50W 2 tone HOT, e.g. too much standing current when cold! But this only delayed the problem, not fixed it! On a different IC735 I had seen PA Bias failure of the Bias emmitter follower & that produced the typcal no RF output at low levels.. PEAK ´ .ÄÄ. .ÄÄ. Round peak PEAK ´ .ÄÄ. No .ÄÄ. RF ³ /::::\ /::::\ ³ /::::\ Gain /::::\ ³ ³::::::³ ³::::::³ Sharp Null ³ ³::::::³Xover³::::::³ ³ ³::::::::³ ³::::::::³V³ ³³::::::::³ ³::::::::³ ´X::::::::::X::::::::::X ´´::::::::ÃÄÄÄ´::::::::à ³ ³::::::::³ ³::::::::³ ³ ³³::::::::³ ³::::::::³ ³ ³::::::³ ³::::::³ ³ ³::::::³ ³::::::³ ³ \::::/ \::::/ ³ \::::/ \::::/ ³ `ÄÄ' `ÄÄ' ³ `ÄÄ' `ÄÄ' When Bias OK No BIAS But this fault was confusing.. PEAK ´ .ÄÄ. .ÄÄ. Round peak PEAK ´ .Ä. Lower .Ä. RF ³ /::::\ /::::\ ³ /:::\ Gain /:::\ ³ ³::::::³ ³::::::³ Sharp Null ³ ³:::::³Xover³:::::³ ³ ³::::::::³ ³::::::::³V³ ³ _-:::::::-_ _-:::::::-_ ´X::::::::::X::::::::::X ´ú:::::::::::ú:::::::::::ú ³ ³::::::::³ ³::::::::³ ³ ³ ~-:::::::-~ ~-:::::::-~ ³ ³::::::³ ³::::::³ ³ ³:::::³ ³:::::³ ³ \::::/ \::::/ ³ \:::/ \:::/ ³ `ÄÄ' `ÄÄ' ³ `Ä' `Ä' When COLD OK When HOT So I have had another look at the problem, with a 100MHz scope, & I looked at the class A stage in the PA unit. I saw it was "taking off" @ VHF when the distortion occurred! 100mW 2W 15W >100W ÚÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ³ RIG's³ ³CLASS³ ³CLASS B ³ ³CLASS B ³ ³SELECTED³ ³ SWR ³ ³ ÃÄ>Ant ³ SSB ÃÄÄÄÄÄÄ´ A Æ͵PUSHPULLÆ͵PUSHPULLÃÄ´ BAND ÃÄ´BRIDGEÃÄ´RELAY³ ³EXCITER³ coax ³STAGE³ ³ DRIVER ³ ³ OUTPUT ³ ³FILTERS ³ ³ ³ ³ ÃÄ>Rx ÀÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÙ ÀÄÄÄÄÄÙ ------------------ PA COMPARTMENT ---------------------- The parasitic oscillation is above HF so it does not get far in the rig. The fault is nothing to do with the class B driver bias as I thought, except that affects the load seen through the driver transformer from the push pull class B stage. ±±± ±±± The instability of the class A stage .Ä. ±±±±± .Ä. at VHF is affected by class B driver ³ /:::\ ±±±±± /:::\ stage's bias setting! ³ ³:::::³±±±±±³:::::³ ³ _-:::::::-_±_-:::::::-_ What seems to be happening when hot, ´ú:::::::::::ú:::::::::::ú is that stage takes off until the HF ³ ~-:::::::-~±~-:::::::-~ drive causes load to be seen on the ³ ³:::::³±±±±±³:::::³ collector then it stops or reduces. ³ \:::/ ±VHF± \:::/ ³ `Ä' ±±±±± `Ä' The net effect is the HF gain is ±±± reduced at the low level crossover ±±± part of the 2 tone signal. Class A Stage's Collector THE CURE CLASS A STAGE CIRCUIT I doubled the NFB base to collector by paralleling +12VÄÄÄÄÄÄÄÄÂÄÄÂÄÄÄÄÄ another 470R across the ³ ³ ÚÄÄÄÄÄ> To Push 470R & all was then tame. 270R )||(__ Pull Class ³ )||( ³ B Driver Q1 transistor seemed to ÚÄ´ÃÄ470RÄÂÁÄÄÙ ÀÄ)ÄÄÄ> Stage have too much VHF gain in ³ ³ ³ this stage when hot & ³ ³/ ³ caused the oscillation! >ÄÄ´ÃÄÂÁÄÄÄÂÄÄÄ´Q1 ³ ³ 220R ³\e 47uÃÄÄÄÂÄÄÄ¿ Bias Component tests around 330R ³ ÃÄÄÄ¿ === 68R _³_Diode this stage found ³ ³ 2n2=== 4R7 ³ ³ \_/ nothing wrong! ÄÂÄÄÄÄ)ÄÄÄÄÁÄÄÄÄÄÁÄÄÄÁÄÄÄÄÄÄÁÄÄÄ)ÄÄÄÄÁÄÄ ÀÄ´ÃÄ´ ³ 150R 100R<ÙDriver +7VTx ÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Bias See my TECH Bul "AF 2 Tone Test Osc Design", "QRO 1kW HF Metered Dummy Load", "IC 735 No RF Output","IC 735 Battery Backup Mod", & "Autocaller with old Maplin kit" Why don't U send an interesting bul? 73 de John G8MNY @ GB7CIP
Read previous mail | Read next mail